Nghĩa của từ tape hole diameter draft bằng Tiếng Việt

@Chuyên ngành kỹ thuật
@Lĩnh vực: xây dựng
-dưỡng đo đường kính lỗ

Đặt câu có từ "tape hole diameter draft"

Dưới đây là những mẫu câu có chứa từ "tape hole diameter draft", trong bộ từ điển Từ điển Anh - Việt. Chúng ta có thể tham khảo những mẫu câu này để đặt câu trong tình huống cần đặt câu với từ tape hole diameter draft, hoặc tham khảo ngữ cảnh sử dụng từ tape hole diameter draft trong bộ từ điển Từ điển Anh - Việt

1. This hole was a scant .23 inches in diameter.

2. The pilot diameter should match the diameter of the hole the Counterbore will be used in.

3. For cutter hole diameter is the diameter of the cutter that the Arbor is compatible with

4. The screw penetration hole has a diameter which is larger than the maximum diameter of the thread of the screw and the center hole formed in the washer.

5. 2pcs 12mm Hole Diameter 45# Steel Tapered Bevel Gear 1.5 Module 16 Teeth

6. Silver open scroll pattern with Black Antiquing large hole beads, 8mm x 8mm, hole diameter 6mm, package of 100 EleganciaBeads

7. Schedule 80 Bulkheads do need a slightly larger diameter hole than ABS Bulkheads

8. This is the diameter of the Counterbore's pilot, which should match the diameter of the hole the Counterbore will be used in

9. Broaching process is used to clean any pre-existing hole or increase its diameter

10. If the pilot diameter is larger than the hole, then the Counterbore won't fit

11. Paper staplers, hole punchers, pencil sharpeners and adhesive tape dispensers for household and commercial use

12. The bonding surface of an adhesive tape is exposed within the recessed groove through the through hole by bonding the adhesive tape in the bottom side.

13. At Bittele Electronics the hole size for Castellated holes must be at least 0.5mm in diameter with space between hole edges to be at least 0.4mm.

14. Roughneck Auger type Post Hole Digger for digging and scooping out a hole of 125mm (5in) diameter, has a hardened blade that will cut through most soils and clays

15. Self adhesive tape, insulating tape, masking tape

16. Tin Anodes are supplied drilled with a 3/8″ Diameter hole and tapped (16 thread) to 1-1/4″ deep.

17. Iron or steel nuts turned from bars, rods, profiles, or wire, of solid section, of a hole diameter ≤ 6 mm

18. Chad definition, a small paper disk or square formed when a hole is punched in a punch card or paper tape

19. Also, the paper analyses the error caused by capillary action of liquid, error precision, zenith angle of hole and container diameter.

20. 11 words related to Audiotape: DAT, digital Audiotape, audio recording, sound recording, audio, tape recording, taping, tape, mag tape, magnetic tape, tape

21. True mean draft = Draft Amidships + correction

22. 18 Industry adhesive tape Unit: producing Mylar tape, Margin tape, Polyimide (finger) tape, Teflon tape and other types with high –temperature.

23. The Barcor Chamfer Gage is a precision instrument designed specifically to measure the top (major) diameter of a Chamfer, countersink or tapered hole

24. The sizes of Countersinks in each set depend on the diameter of the hole; in all sets, the vertex angle is 60°.

25. Adhesive tape, dispensers for adhesive tape