Nghĩa của từ finite element method bằng Tiếng Việt

@Chuyên ngành kỹ thuật
-phương pháp phần tử hữu hạn
@Chuyên ngành kỹ thuật
-phương pháp phần tử hữu hạ

Đặt câu có từ "finite element method"

1. This is the power of the finite element method.

2. 2 This is the power of the finite element method.

3. Key words: alkali–aggregate reaction, concrete dams, finite element method, dam safety.

4. Analyze load behavior of sluice with method of - dimension - linearity finite - element method.

5. The aeroelastic equations of the beam were solved using the finite element method (FEM).

6. The development of computer and finite element method, proffer a new way for this research.

7. The finite element method was used for analysis of heat stress in chip on board ( COB ).

8. The tidal current field of Jiaozhou Bay is numerically simulated using the splIt'steps finite - element method.

9. For a three-layer, phenolic-resin-bonded particleboard, the stresses are calculated, using the finite-element-method.

10. Key words : critical slip surface, dynamic programming, factor of safety, finite element method, limit equilibrium method, slope stability.

11. The temperature distribution in the diamond synthesis cell of sideward heater was investigated theoretically by finite element method (FEM).

12. A finite element method is employed to calculate the characteristics of TE0nm-resonances of axisymmetric dielectric structures for permittivity measurement.

13. The finite element method was used for the calculation of the steady-state three-dimensional (3D) flow of unconfined groundwater.

14. 16 The nonlinear stability of the space frame-composite laminate plate combined structures is studied by nonlinear finite element method.

15. Simulations concerning the thermomechanical behaviour of a SiC whisker-reinforced aluminium alloy are carried out with the finite-element method.

16. Finally, the torsion vibration nature frequency and torque amplitude factor of a rolling mill are calculated by using finite element method.

17. Based on a magnetic strain model, the basic equation of finite element method for magnetoelastic bucking analysis is derived in this paper.

18. The paper presents a number of alternative procedures for the solution of elasto-plastic problems by the matrix displacement or finite element method.

19. 27 To make a better understanding of joint mechanics behaviors, this thesis studies joints of T-section steel truss with finite element method (FEM).

20. The optimization aimed at decreasing deform force of forging is carried out. Based on rigid viscoplasticity finite element method, the optimization design is studied.

21. 15 In this paper, finite element method is used to the computation of the equivalent resistance network for multilevel packing structure with arbitrary boundary.

22. 6 In the two-dimensional interpretation, we adopt the point source finite-element method and the reciprocity principle which can lighten the calculation burden.

23. 21 The bulk metal forming processes are calculated and analyzed by using a multi- step finite element method (FEM) based on deformation theory of plasticity.

24. In this research the finite element method is applied to analyze the circular fiber-reinforced isolators for different shape factor and compressibility of elastic layers.

25. 7 Finite element method is applied to solve the field with the temperature field characteristic, then the ampacity of buried cables is received after iterative computation.

26. To calculate magnetic fields with arbitrary material distributions and excitations the given vector potential differential equation is transformed into an algebraic system of equations (Finite Element Method).

27. 30 The effect of elastic modulus of adhesive on the str ess distribution in aluminium alloy single lap joint was investigated using elastic-plastic finite element method(FEM).

28. Turbulent compressible flow past an asymmetric trailing edge has been computed using the generalised-coordinate time-split group finite-element method and a lagged algebraic eddy viscosity turbulence model.

29. In order to improve the office paper feeder design and minimize paper jam fault in running office equipment, paper mechanical properties are studied by means of nonlinear finite element method.

30. First, using the finite-element method, numerical Backscatterings of metallic and dielectric targets behind a cinder block wall are calculated and the effects of the wall on images are investigated

31. Using enthalpy to deal with latent heat of solidification the numerical model is solved by finite element method, and a steady temperature field can be obtained under a certain condition.

32. 29 According to the structural feature of parallel single disk gate valve, the strength and rigidity of body will be calculated with finite element method, and with cylindroid shell theory.

33. A three-dimensional model of the left acetabulum with inserted threaded cup has been generated, based on the finite element method, to calculate stress patterns in the standing phase during walking.

34. 24 In architectonics , the calculation of rectangular plate on elastic foundation, in common, is used by the finite element method and chart. It is difficult to obtain the universal analytic solution.

35. The main idea of this algorithm is based on the application of a modified gradient method for solving the overdetermined, nonlinear system of algebraic equations obtained by the finite element method.

36. A two-dimensional heat conduction equation with a time dependent aerodynamic heating condition at one surface and a radiation boundary condition at the other end is solved using finite element method.

37. 18 The shredding process of steel scrap was simulated through FEM software ANSYS/LS-DYNA based on Nolinear finite element method. The simulating results that steel scrap is shredded are acquired.

38. This paper obtains the mode of vibration of swash plate in an axial piston pump by finite element method, which is verified by experimental results. And on the basis, some discussions are carried out.

39. Different methods for a visualization of plate vibration modes are compared: a laser scanning vibrometer, a microphone scanning in a very near field, a near field acoustic holography, an analytical calculation, and a finite element method calculation.

40. It includes a variational approach based on Rumsey reaction concept. The problem is numerically solved with a surface finite element method : surfaces of 3D conducting object and interfaces between dielectric domains are meshed using surface triangular patches.

41. The time-averaged motion of shore-fast ice near a small Arctic island is analysed through the solution of the momentum equation for the ice cover using the Galerkin finite element method coupled with an adjoint sensitivity formulation.

42. The sharp edges and tips boosted SERS activity was proved by the finite element method modeling of the plasmonic properties of Ag nanotriangles with different edge thicknesses (10 − 80 nm), Ag nanosheets with different tip Acutances (squares and hexagons) together with Ag nanorods, nanocubes and nanospheres

43. ‘Three-node triangular Axisymmetric elements were used for spatial discretization of the plasma.’ ‘Perfect aperture circularity is necessary to obtain an Axisymmetric liquid curvature.’ ‘The finite element method has failed to replace the conventional SSI method in the laterally-loaded pile problem because the lateral load is not