Nghĩa của từ internal yield pressure strength bằng Tiếng Việt

@Chuyên ngành kỹ thuật
@Lĩnh vực: hóa học & vật liệu
-giới hạn độ bền áp suất

Đặt câu có từ "internal yield pressure strength"

Dưới đây là những mẫu câu có chứa từ "internal yield pressure strength", trong bộ từ điển Từ điển Anh - Việt. Chúng ta có thể tham khảo những mẫu câu này để đặt câu trong tình huống cần đặt câu với từ internal yield pressure strength, hoặc tham khảo ngữ cảnh sử dụng từ internal yield pressure strength trong bộ từ điển Từ điển Anh - Việt

1. Internal pressure sensor.

Cảm biến nội áp suất.

2. Key words: code calibration, geometric properties, reliability, steel, tensile strength, yield strength.

3. Re= yield strength in N/mm2, or 0,2 % proof strength or, for austenitic steels, 1 % proof strength;

4. Ideally, the surface should yield slightly under pressure.

5. 16 Ideally, the surface should yield slightly under pressure.

6. Blown: enlarged beyond normal from internal pressure.

7. Pressure-sensitive adhesive composition having high shear strength

8. Autogenous deformations, internal relative humidity and compressive strength were recorded.

9. To open and suddenly come apart from internal pressure.

10. The internal pressure and discharge rate of the aerosol dispenser;

11. Low alloy steel with a high yield strength and high sulphide stress cracking resistance

12. Yield strength is the lowest stress that produces a permanent deformation in a material.

Độ bền uốn là ứng suất thấp nhất làm biến dạng vĩnh viễn cho một vật liệu xem xét.

13. The yield strength of pure aluminium is 7–11 MPa, while aluminium alloys have yield strengths ranging from 200 MPa to 600 MPa.

Sức bền của nhôm tinh khiết là 7–11 MPa, trong khi hợp kim nhôm có độ bền từ 200 MPa đến 600 MPa.

14. Internal pressure drop of additional non-ventilation components (Δps, add)

15. As the temperature falls below # °C the ultimate strength (Rm) and the yield strength (Rp # ) increase slightly for all aluminium alloys (see figure

16. Pressure-sensitive adhesives exhibiting an improved shear strength at elevated temperatures

17. Front Axles Forged from 4340 material & heat treated for high tensile and yield strength. Increased material in the yoke area for added strength

18. Bending strength, internal bond and hardness of all polystyrene treated particleboards were improved.

19. As the temperature falls below 0°C the ultimate strength (Rm) and the yield strength (Rp0,2) increase slightly for all aluminium alloys (see figure).

20. Burst: to break open or into pieces usually because of internal pressure

21. Except for UN No 1001 acetylene, dissolved, the permissible maximum stress of the manifolding arrangement at the test pressure of the receptacles shall not exceed 75 % of the guaranteed yield strength of the material.

22. This may have to do with “Antigravitational” extensor strength being a more relevant determinant of the knee joint internal forces than flexor strength

23. Crustal deformationoccurs when applied forces exceed the internal strength of rocks, physically changing their shapes

24. The flywheel material with the highest specific tensile strength will yield the highest energy storage per unit mass.

Vật liệu bánh đà với độ bền kéo cao nhất cụ thể sẽ mang lại lưu trữ năng lượng cao nhất cho mỗi đơn vị khối lượng.

25. Aluminized steel was developed for providing more structural durability and a high yield strength in highly corrosive environments