Nghĩa của từ bandpass filter bằng Tiếng Việt
@Chuyên ngành kỹ thuật
@Lĩnh vực: toán & tin
-bộ lọc lấy dải
Đặt câu có từ "bandpass filter"
1. The ideal Bandpass filter and the practical Bandpass filter frequency response is as shown in figure
2. Advantage of using a Bandpass filter: An active Bandpass …
3. A bandpass filter passes signals having a frequency within a predetermined band characteristic of moving vehicles.
4. The varactor shunt switches can be used to create a bandpass filter and a tunable notch filter.
5. Thirdly, a dual-mode dual-band bandpass filter with rectangular-loop perturbation and stacked structure is presented.
6. A Bandpass filter (BPF) is an electronic circuit that passes a certain band of frequency without attenuation
7. A Bandpass filter is useful when the general location of the noise in the frequency domain is known
8. The Bandpass filter allows frequencies within the chosen range through and attenuates frequencies outside of the given range.
9. Disclosed is an electric filter comprising a bandpass filter (100) that encompasses a track with acoustically coupled electroacoustic transducers (11, 12, 13).
10. The FSQ-BG40 Colored Glass Bandpass Filter is a 50.8 x 50.8 mm square, blue Bandpass optical filter made of Schott BG40 filter glass
11. 26 It proves by practising that this designing method of microstrip pectinate bandpass filter and interlaced digital filter is simple and of good effect.
12. The series element (21, 22) of the band-stop filter is serially connected to at least one of the transducers (11, 12) of the bandpass filter.
13. A band-pass filter or Bandpass filter (BPF) is a device that passes frequencies within a certain range and rejects (attenuates) frequencies outside that range.
14. Filters come in basic classes: low-pass filters (LPF), high-pass filters (HPF), and Bandpass filters (BPF, and the notch filter (the inverse of the Bandpass filter) (Figure 1)
15. The delay can be adjusted by tuning the dielectric monoblock bandpass filter and/or the reactive termination resonators and/or the coupling capacitors defined by the dielectric ceramic reactive termination block.
16. Also a bandpass filter is constructed by combining frequency responses for sine components of absolute values integrated from 0 to bpf and sine components of absolute values integrated from 1 /bpf to 0.
17. Another point made late, but instead pitching down Abiences to slow them, I put them through a bandpass filter, cutting off all the highs down to 2k and anything below 100hz; and then send that through a reverb and some of that signal through a VERY slow …
18. ‘The multiplex type filter contains at least two disparate Bandpass filters for separate reception or transmission frequency bands.’ ‘You can also change volume and reverb levels on each track, adjust resonance and center frequency of a simple Bandpass filter, and change pitch and tempo globally.’
19. Bandpass filter, M-411CB, frequency range 11 meters, 26.9-27.4 MHz $66.50 I live 3 miles from a 50kw clear channel AM station in Atlanta (AM 750 WSB) and it pretty much chewed up 20m and 80m, The Morgan filter was the perfect solution.
20. As you see that the Band pass filter has the infinite attenuation for the blocked frequencies and zero attenuation for passband frequencies.; But in practical this is not possible, the practical Bandpass filter offers of zero to one dB attenuation for passive filters which also depends on …
21. The Bandpass filter response (Figure 6.1C) is essentially overlaid LPF and HPF responses.There are two cutoff frequencies: a lower limit (F 1) and an upper limit (F H), both of which are defined a t −3 dB points.The bandwidth of the BPF is defined as the difference between −3 dB points: