Nghĩa của từ ductility bằng Tiếng Đức
ductility [dʌktilitiː] Streckbarkeit
Đặt câu có từ "ductility"
1. This property is known as ductility.
2. Excellent toughness and ductility in all directions.
3. Ductility is an important problem in the research of HSC.
4. The larger the thermal gradient, the lower the anisothermal ductility.
5. The hysteretic curve of the damper with concrete ductility column is plumper.
6. Silicon bronze has the ductility of copper but much more strength.
7. With high ductility and impact strength . E . g . Automotive safety parts.
8. Oxygen free Coppers are used in applications requiring high conductivity and exceptional ductility
9. Wear resistant austenitic steel having superior machinability and ductility method for producing same
10. Key words: seismic, excitation, response, spectrum, accelerogram, building, drift, curvature, ductility.
11. A parametric study of ductility of T beams has been conducted.
12. In addition, Annealing reduces the brittle tendencies of PLA by increasing ductility.
13. Amenability: noun accessibleness , acquiescence , adaptability , agreeableness , compliancy, conformability , docility , ductility , flexibility , flexibleness
14. Analysis shows that the confined concrete can obviously improved bearing capacity and ductility.
15. Ductility allows a metal or alloy to be drawn into a wire.
16. Three reinforcement test piers' ductility is analyzed through hysteric curve and skeleton curve.
17. Annealing increases ductility and lessens the possibility of a failure by relieving internal strains
18. The increase in ductility can be attributed to the increase in ratio of transgranular fracture.
19. Tests used to assess the ductility and malleability of stainless steel subjected to bending.
20. Ductility . A ductile material is one which can be drawn out permanently by a tensile force.
21. Ductility is a measure of the degree of plastic deformation that has been sustained at fracture.
22. The copper alloy has a local ductility index of greater than 0.7 and a tensile elongation exceeding 5 %.
23. Typically, in steels, Annealing is used to reduce hardness, increase ductility and help eliminate internal stresses.
24. Unlike adhesively-bonded plates, Bolted plates can exhibit a large amount of ductility as shown in Fig
25. The Brittleness manifests as a minimum in the ductility and impact strength as a function of temperature.
26. When hydrogen is absorbed by steels and other alloys, it reduces their ductility and load bearing capability.
Wenn Wasserstoff von Stahl und sonstigen Legierungen absorbiert wird, dann wird deren Duktilität und Traglastfähigkeit verringert.
27. The ductility of alabaster, on the other hand, makes it particularly suited to the sculpturing of minute details.
Da er sich leicht bearbeiten lässt, eignet er sich jedoch ausgesprochen gut für die Gestaltung feinster Details.
28. Annealing is a heat treatment process used mostly to increase the ductility and reduce the hardness of a material. This change in hardness and ductility is a result of the reduction of dislocations in the crystal structure of the material being Annealed.
29. Annealing is a heat treatment process used mostly to increase the ductility and reduce the hardness of a material
30. Based on the properties of moderate -high-rise multi - bibbed composite wall structure, displacement ductility design method is investigated.
31. Key words: columns, confinement, ductility, high-strength concretes, lightweight aggregate concretes, reinforcement, stress–strain relationships, tests, ties, toughness.
32. Annealing is commonly used to: Soften a metal for cold working; Improve machinability; Enhance electrical conductivity; Annealing also restores ductility
33. The cross- section curvature ductility ratio for R. C inequiaxial T - shaped, l-shaped and cress - shaped columns is calculated by numerical method.
34. The results shows that the lateral deformation was confined effectively and the ultimate compressive strength was increased, the ductility was improved.
35. There are many who cannot understand the differences between ductility and Brittleness and this article is meant to explain the differences between
36. The structural earthquake action value is correlated with the structural overstrength, structural ductility and overstrength can be reflected by the structural influencing coefficient.
37. The mechanical performance of Crazed polycarbonate was characterized by measuring the yield stress, elastic modulus, failure stress, and ductility for constant strain rate tensile tests.
38. To improve the toughness and the ductility of the glutinous rice paper product, some factory illegally add PVA to glutinous rice paper.
39. 19 To improve the toughness and the ductility of the glutinous rice paper product,[www.Sentencedict.com] some factory illegally add PVA to glutinous rice paper.
40. Process Annealing is carried out intermittently during the working of a piece of metal to restore ductility lost through repeated hammering or other working
41. Accelerated aging was achieved by using low pressure steam curing. The strength and ductility of GFRC sheets were measured by the direct tension test.
42. The production of light nodular graphite iron parts with high ductility in investment casting was expounded in all aspects including both technological analysis and processing control.
43. The cold-rolled and twisted bars, which have many advantages such as high strength, superior bondability and reliable ductility, are widely used in floor framing system.
44. The present paper has introduced in detail the pilot production and research and development of cemented carbide printing needle with high ductility used for electronic printer.
45. Annealing, treatment of a metal or alloy by heating to a predetermined temperature, holding for a certain time, and then cooling to room temperature to improve ductility and reduce brittleness
46. Brittleness, on the other hand is exactly an opposite property of ductility as it is the ability of a material to break without first undergoing any kind of deformation upon application of force
47. Annealing in metallurgy and materials science is a heat treatment that alters the physical properties (and sometimes chemical properties) of a material to increase its ductility (ability to be shaped without breaking) and reduce its hardness.
48. Some authors in the mining industry define Brittleness index B (loosely defined, but the concept is also called Brittleness ratio, Brittleness coefficient, or ductility number) as the ratio of uniaxial compressive strength to tensile strength.
49. Brasses are a range of cast and wrought copper alloys made up of copper and zinc, with differing combinations of properties, including strength, machinability, ductility, wear-resistance, hardness, colour, electrical and thermal conductivity, and corrosion resistance.
50. As a master alloy, Cerium-copper can be used for grain refining, hardening, and improving copper alloy performance by enhancing properties such as ductility and machinability.Available alloy forms include sheets and plates, discs, foils, rods, tubes, and other shapes.