1. The shearing strength is one of the main indexes of rock mass.

2. Two-step shearing method for preventing damage of press-cutting die for high-strength material

3. Key words: box girder, ship's hull, bending, ultimate strength, residual strength, residual stresses, initial imperfections.

4. It is both her incomparable strength and her ultimate limitation.

5. Key words: connections, design tables, eccentric, fillet welds, limit states, ultimate strength.

6. The results show as the moisture increased, the internal friction angle and cohesive strength decrease with shearing strength reduced, which is the prime reason of the slope.

7. Shearing of Wool

8. As the temperature falls below # °C the ultimate strength (Rm) and the yield strength (Rp # ) increase slightly for all aluminium alloys (see figure

9. He set the ultimate example in loving Jehovah with his whole mind, heart, soul, and strength.

10. As the temperature falls below 0°C the ultimate strength (Rm) and the yield strength (Rp0,2) increase slightly for all aluminium alloys (see figure).

11. • Develop methods and devices to better predict the ultimate strength of tension, bending, shear and compression.

12. Sheep are generally washed before shearing .

13. They are shearing the wool off.

14. The farmer is shearing his sheep.

15. The average yield is about 1.5 kilograms per shearing .

16. The shearing strain is essentially inhomogeneous flow of metal.

17. Chromatin Shearing Covaris workflows enable standardized Chromatin shearing from versatile samples such as primary cells, cultured cells, tissues, and FFPE samples

18. Bending , folding , flattening , shearing , punching and notching machines : * *

19. The main horizontal shearing angle, in degrees

20. They use electric shears for sheep shearing.

21. Sheep shearing is a highly skilled craft.

22. I'll go to see you after shearing.

23. CNC machined from a wafer thin strip of ultralight aluminum, the Iain Sinclair Cardsharp4 Knife has ultimate robustness and strength

24. Strain-Ageing is known to cause an increase in yield strength and ultimate tensile strength of reinforcing steel bars, while tensile elongation capacity will be less in strain-aged steel bars

25. He found a job of shearing wool from sheep.

26. The results shows that the lateral deformation was confined effectively and the ultimate compressive strength was increased, the ductility was improved.

27. They will be shearing the sheep next week.

28. Tannery machines - Splitting and bandknife shearing machines - Safety requirements

29. Tannery machines — Splitting and bandknife shearing machines — Safety requirements

30. Adhesive joints are in general subjected to combined normal and shearing stresses.

31. Capable of or designed for incising, shearing, or severing: a Cutting tool.

32. Nevertheless the allenthesis used should be built as stable as possible in order to intercept the influencing forces, especially those which challenge the shearing strength of synostosis in spite of anatomic reposition.

33. There' s a shearing effect when alloys of different density abrade

34. Aligning by light. helpful to mark out by hand for shearing.

35. 7 Now I hear that you are doing your shearing.

36. 18 After analyzing the response of SRC column with different durations, slenderness ratios or eccentricities , the equations of ultimate strength are derived by regression.

37. The deformation includes well-developed stretching lineations and shearing zones.

38. Machines for bending, folding, straightening, shearing, punching and notching metal, not numerically controlled

39. The uplifting, right-lateral strike-slip shearing, tilting and southward shearing of the Altai Mountains in Xinjiang have affected, since Oligocene, the drainage systems evolution and development.

40. The tangent of the shearing angle corresponds to the demagnetization factor N.

41. Others, like the horned triceratops, were clearly adapted to shearing plant material.

42. Set up strong wind water shearing and hot air cycle drying system.

43. Aligning by light , helful to mark out by hand for shearing.

44. To reduce Crooking it is recommended to use a smaller shearing angle and to …

45. When the time came for shearing the flock, David asked Nabal for some provisions.

46. A typical contract ran from one annual shearing to the next.

47. It features ultimate tensile strength exceeding that of leading Acellular matrices, and maximum suture pull-out values for more assurance in surgical repair of soft tissue

48. Measuring apparatus for measuring the shearing resistance of floors, walls and screed

49. Based on Shearing Stress Theorem, we know that the shearing stress direction of all the spots on the edge of circular cross-section should be tangent to the circle.

50. The ultimate knowledge.

51. Machines for bending, folding, straightening, shearing, punching and notching metal, numerically controlled

52. These include tensile strength, wet and dry tear strength, burst strength, air permeability, seal strength and integrity.

53. Key words: concrete, accelerated strength, tensile strength, admixtures, curing, splitting tensile strength, modulus of rupture, strength correlations.

54. His great sword Clanged down, the edge shearing sparks against the granite stair.

55. Transducers must be fitted to measure knee-bending angle and knee-shearing displacement

56. Transducers shall be fitted to measure knee bending angle and knee shearing displacement.

57. He remembers seeing blind pianist George Shearing perform in Bisbee, of all places.

58. Ultimate Arachnid (Savage World) The Ultimate Arachnid is from the Savage World Universe

59. – machine tools (including presses) for working metal by bending, folding, straightening, flattening, shearing, punching or notching

60. In chain termination reaction station, adding some urea, the shearing stability of grease is improved greatly.

61. Argos goes from strength to strength

62. – machine tools (including presses) for working metal by bending, folding, straightening, flattening, shearing, punching or notching | | |

63. Transducers must be fitted to measure knee-bending angle and knee-shearing displacement.

64. Shearing in Egypt is done once or twice a year with hand clippers.

65. The distribution of storey shearing force in frame - shear wall structure is discussed.

66. Without Ultimate Accelerants, her …

67. It features a crossover between the Ultimate X-Men and the Ultimate Fantastic Four.

68. Shearing should , therefore , be done when the weather is neither too cold nor too hot .

69. The two additions are separated by a step for shearing the fibrous suspension (or mass).

70. Ultimate Beatnik Collection, Vol

71. High strength adhesives with impact peel strength

72. The procedure is based on applying a sinusoidally alternating shearing stress to the substance.

73. The earliest preserved structures are penetrative foliations and stretching and mineral lineations recording regional ductile shearing (D1).

74. Since 1948, Copex is designing and manufacturing equipment for the compacting and shearing of scraps and metals.

75. Shearing: Shifting of the working point on the demagnetization curve by opening the previously closed magnetic circuit.

76. Grandpa was a strong man and was good at shearing sheep in the days before electric clippers.

77. Until the ultimate check-out.

78. It's the ultimate geographical suicide.

79. It's like this ultimate toolkit.

80. Power is the ultimate aphrodisiac.