1. Piezoresistive resistor

2. Another common type of resistor is the thin-film resistor.

3. Rescalc will respond with standard resistor values, listed by accuracy or ascending value, for series or parallel combinations.

4. Resistor fabrication

5. a resistor,

6. The modifications include adjusting a length of the resistor, forming a compound resistor structure, and forming a replacement resistor.

7. Circuit-Horizontal Resistor (European

8. Chip resistor substrat

9. 3.7 Resistance/Resistor

10. Adjustable mos resistor

11. — terminating resistor 50 Ohms

12. — Terminating resistor 50 Ohms

13. Adjustable fluid flow resistor

14. Terminating resistor 50 Ohms

15. Circuit-Vertical Resistor (European

16. Ceramic resistor or sensor element

17. Let's say resistor 2 is 3 ohms, and let's say resistor 3 is 5 ohms.

18. Adjustable fluid flow resistor cassette

19. A Bleeder resistor is a standard resistor connected in parallel with the output of a high-voltage power supply circuit for the purpose of discharging the electric charge stored in the power supply’s filter capacitors when the equipment is turned OFF

20. A process tunable resistor is fabricated by adjusting elements of the resistor during a fabrication process.

21. Fuse resistor, and method for manufacturing same

22. Memory resistor adjustment using feedback control

23. Simple configurations using standard voltmeters and Ammeters have limited accuracy, because the meters alter both the voltage applied to the resistor and the current flowing through it

24. Let's say resistor 1 is 2 ohms.

25. So we can just draw each resistor separately.

26. Film thermal resistor is one of temperature sensors.

27. Using high precision resistor, capacitor, IC with low noise.

28. For transformer, capacitor, resistor and electronic component lead cutting.

29. Portable electric device for adjusting a variable resistor

30. I think there's something wrong with the resistor.

31. Adjustable resistor with slider made from elastomeric material

32. But each resistor only sees the voltage source.

33. A current-limiting resistor is usually not necessary.

34. Function as a resistor in normal operation condition.

35. Biasing using a Drain-to-Gate Feedback Resistor 4

36. Detector for force, acceleration and magnetism using resistor element

37. When the resistance value of the adjustment resistor (R¿P?)

38. The first semiconductor logic family was resistor–transistor logic.

39. Note: All outputs are protected by 470 Ohm resistor.

40. A voltage drop across the adjustment resistor (R¿P?)

41. Physically, the resistor is effectively the source of noise.

42. The drive includes a resistor and an output transistor.

43. Temperature set point circuit and method employing adjustment resistor

44. Terminating resistor # or # Ohms depending on radio-set type

45. The second resistor has been replaced by a capacitor.

46. The Bolometers developed at IPP are miniaturized metal resistor Bolometers

47. The Bolometers ITER will use are miniaturized metal resistor Bolometers.

48. A chip resistor array is manufactured by the following method.

49. Electronics-Salon Thick Film Network Resistor Assortment Kit, Array Resistor, Bussed Type, 1/8W, SIP-5 and SIP-9 470 1K 4.7K 10K 47K ohm.: Amazon.com: Industrial & Scientific

50. Switchable junction with an intrinsic diode formed with a voltage dependent resistor

51. In addition, a detuning resistor (K) is provided that can optionally be connected, directly or indirectly in parallel, to at least one resistor in the Wheatstone bridge.

52. Each Bypassed resistor voltage grading and safe discharge after switching off

53. For example, if a 300 ohm resistor is attached across the terminals of a 12 volt battery, then a current of 12 / 300 = 0.04 amperes flows through that resistor.

54. The resistor is linear, symmetrical and adjustable by varying biasing levels.

55. — Terminating resistor 50 or 75 Ohms depending on radio-set type.

56. Rescalc 0 resistor calculator has been much improved since its original release.

57. To each switch is allocated a measuring resistor (R), these measuring resistors (R) forming a resistor network with a node to receive a quasi-analog acceleration signal (a).

58. Adjustible resistor for use in a resistive divider circuit and method for manufacturing

59. The flow resistor (18, 28) can be positioned against an abutment such that the resistor elements (20a, 20b, 20c) are compressed when subjected to pressure by the aerated liquid.

60. The invention also relates to a method for producing said resistor assembly.

61. I don't know, just for fun, let's throw in a third resistor.

62. Four-terminal resistor with four resistors and adjustable temperature coefficient of resistance

63. Scan-Speak Flow Resistor Aperiodic Vent - EACH Cutout size is 4.3 inches

64. In addition there may be sense leads (22, 24) present on the resistor.

65. 2 : involving a single thread or wire doubled back upon itself a Bifilar resistor.

66. Adjust the differential trimmer capacitor until a minimum voltage across resistor R2 is obtained.

67. 23 To test resistor R first energize Ch. 1 to bias the test coupon.

68. In addition, the SCXI-1520 system offers a half-bridge completion resistor network in the module and a socketed 350 Ω quarter-bridge completion resistor in the SCXI-1314 terminal block.

69. From Ohm's law, the voltage difference across the resistor is therefore about 350 mV.

70. SMD/SMT Bussed 8 Resistor Networks & Arrays are available at Mouser Electronics

71. Compute the voltage across a 120W termination resistor when using 1150W Biasing resistors.

72. The Biasing is created by self, using the voltage drop across source resistor

73. Polycrystalline silicon e-fuse and resistor fabrication in a metal replacement gate process

74. These resistors are also in series with the resistor in the left tube.

75. To test resistor R first energize Ch. 1 to bias the test coupon.

76. This resistor absorbs the network signals and stops them bouncing back down the wire.

77. There are several logic families with different characteristics (power consumption, speed, cost, size) such as: RDL (resistor–diode logic), RTL (resistor-transistor logic), DTL (diode–transistor logic), TTL (transistor–transistor logic) and CMOS.

78. This meter measures a potential drop across resistor 1, and is about 9 volts.

79. The resistor is disposed on a handle unit between first and second conductive parts.

80. The heating resistor (12; 43) is subjected to a periodically changing heating voltage (UH(t)), the frequency (f0) of which is adjustable, such that the heating resistor couples temperature waves into the medium (24).