1. When diameter tolerance is specified on top of Circularity tolerance, then the Circularity tolerance is always less than the diameter tolerance.

2. Angularity applied on non feature of size creates tolerance zone consists of two parallel planes and all the surface elements must lies within tolerance zone. When Angularity is applied on cylindrical feature of size, tolerance zone is a cylinder, diameter of tolerance value referenced in feature control frame

3. Free Standing Portable Barres Free Standing Portable Ballet Barre with Adjustable Barre on One Side, 1 7/8”, +/- 1/8” Diameter, +/- 1/8” Length Tolerance specifications

4. The Operation had absolutely zero tolerance on SEA.

5. It explains the basic mechanisms of Chimerism-based tolerance and provides an update on ongoing clinical tolerance trials

6. However, surface variations of the controlled diameter can have a direct impact on the end result because a Concentricity tolerance invokes a requirement which is much different than what most people realize.

7. Circularity tolerance is a form tolerance

8. Employer has zero tolerance policy on alcohol use.

9. Playing on the railway embankment was well beyond that tolerance.

10. Clipped washers have a flat edge on either the outside diameter (OD), inside diameter (ID) or both.

11. Tolerance is classified into central tolerance or peripheral tolerance depending on where the state is originally induced—in the thymus and bone marrow (central) or in other tissues and lymph nodes (peripheral).

12. 5 We all need tolerance, oodles of tolerance.

13. We have zero tolerance for predatory behavior on YouTube.

14. The equatorial diameter exceeds the polar diameter by 26 miles.

15. Before profiling the jaws we will take a small cut on the inside diameter of the jaws equal to the plug diameter

16. * Drug tolerance

17. It depends on your financial obligations and your risk tolerance .

18. The tolerance on the control mounting angle shall be ± # degrees of the design angle

19. In the present invention, a diameter tolerance of a metal pipe to be inserted through a clamp is absorbed in order to prevent vibrations of the metal pipe and abnormal noises.

20. The tolerance to the impact velocity is ± 2 % and the tolerance to the impact direction is ± 2°.

21. Extremism became tolerance.

22. Other experiments included evaluating the physical training of muscular strength on acceleration tolerance.

23. The middle strain gauge is located on the symmetrical axis with a ± # mm tolerance

24. On the one hand, this can lead to the so-called “tolerance stack-up”.

25. The indicators are about the ‘Abiotical’ factors such as climate, soil, salt tolerance and heavy metal tolerance

26. The tolerance on the control mounting angle shall be ± 2 degrees of the design angle.

27. The tolerance on the control mounting angle shall be p # degrees of the design angle

28. The tolerance on the control-mounting angle shall be ± 2 degrees of the design angle.

29. From Violence to Tolerance

30. The diameter of a Counterbore is generally slightly larger than the fastener head’s diameter

31. The middle strain gauge is located on the symmetrical axis with a ± 1 mm tolerance.

32. The tolerance on the control mounting angle shall be p 2 degrees of the design angle.

33. Bisiliac diameter: the greatest distance between points on the two fetal iliac crests.

34. The actual diameter of the various Buck shot pellets are: Buckshot Size Diameter (in inches)

35. The pilot diameter should match the diameter of the hole the Counterbore will be used in.

36. The “actual external diameter” is the external diameter measured by the Technical Service prior to the test.

37. Unlike the snap-on Augers, the 12” D-series is a full 12″ diameter.

38. Models based on absolute height or tree diameter were usually weaker.

39. For cutter hole diameter is the diameter of the cutter that the Arbor is compatible with

40. However, with the Concentricity check, one diameter is held in a fixture to set up a reference axis (or the CMM may create an axis based on a few diameter touches on the reference)

41. The Concentricity control specifies that there is a 0.1 dia tolerance cylinder centered on datum [A]

42. I have low alcohol tolerance.

43. What's the length of the diameter?

44. The diameter measures twice the radius.

45. The power module may be configured to adjust the latency tolerance value on a per-frame basis.

46. Check on salt tolerance of your fish especially some of the more delicate catfish before treating.

47. The major diameter of the Chamfer is read directly on the dial or electronic indicator

48. All peacekeepers must abide by the same code of conduct, based on the principle of zero tolerance.

49. All peacekeepers must abide by the same code of conduct, based on the principle of zero tolerance

50. Depending on the sodium tolerance of the amino acid analyser (#.#) proceed according to #.#.#.# or #.#.#.# for the pH adjustment

51. The diameter of the flywheel housing;

52. Resource allocation guided by risk tolerance.

53. Tolerance is one of his strengths.

54. The mirror is 25cm in diameter.

55. We have zero-tolerance to terrorism.

56. Tolerance to alcohol decreases with age.

57. Tolerance is a sign of breeding.

58. The Anteroposterior diameter (DAP) of the tooth is 25.7 mm and transverse diameter (DT) is 10.7 mm

59. The Edict of Nantes—A Charter for Tolerance?

60. There should have been an explicit understanding of the department's risk tolerance on this decision to accelerate.

61. MICRO Collimator Length: 23.37mm (0.92”) Outside Diameter: 6.35mm (0.250”) Material: Stainless Steel Micro Collimator - COL005B0101 & COL005S0101 5mm Lens Diameter, NA of the fiber = 0.22 Beam Diameter (mm) Note: Collimator Divergence (milliradians) = Fiber Diameter (µ) / …

62. Circumference to Diameter Calculator

63. d = actual filament diameter

64. A transcendental number whose value is the ratio high on any circumference to its diameter.

65. It spans about 000 light-years in diameter, compared to the Milky Way's 000 light-year diameter.

66. The method described is useful also for the amylum-tolerance test of the exocrine pancreas in comparison with an oral glucose-tolerance test.

67. Languedoc was a land of tolerance.

68. Mineral part of the soil, fractioned on the basis of size (diameter), limits of the particles.

69. Type of Contaminant Test Test Method Used Medicinal Substance Tolerance Limits Acceptable NHPD’s Tolerance Limits Chemical Contaminants Arsenic

70. Another essence of Chinese traditional culture is the virtue of tolerance, which advocates for tolerance of the dissidence and civilization of alien nature.

71. The Costar® 9RV has a 5" diameter and the SA-339 has a 5.25" diameter

72. Tolerance is love sick with the sickness of haughtiness.

73. Tolerance is love sich with the sickness of haughtiness!

74. The organization promotes racial tolerance and unity in diversity.

75. Objective To investigate the effect of donor blood transfusion on inducing pancreatic allograft tolerance in outbre drat model.

76. Inside diameter-adjustable ring

77. This is the diameter of the shank on the interchangeable pilot that is compatible with the Counterbore

78. The diameter of bolts, on the other hand, must be measured at the crest of the thread.

79. Circularity is a 2-dimensional tolerance zone, which consists of 2 concentric circles whose radius spacing is equal to the tolerance value.

80. The test subjects underwent oral glucose tolerance test ( OGTT ) , anthropometric measurements , overnight polysomnography , and a frequently sampled intravenous glucose tolerance test ( FSIGT ) .