1. At present, the methods of random sampling, systematic sampling and stratified sampling are widely used in remote sensing sampling.

2. Allows customized sampling scenarios through statistical sampling.

3. Circularity tolerance is a form tolerance

4. When diameter tolerance is specified on top of Circularity tolerance, then the Circularity tolerance is always less than the diameter tolerance.

5. 5 We all need tolerance, oodles of tolerance.

6. Adaptive sampling

7. For sampling with impinger: use subcode ‘IM’; active sampling on sorbent: subcode ‘AS’; diffusive sampling: subcode ‘DI’.

8. In certain situations, the non - sampling error even surpasses the sampling error to the sampling result influence.

9. Sampling of male Arrestees and purposive sampling of female Arrestees

10. * Drug tolerance

11. Aseptic sampling involves the use of sterile sampling implements and containers

12. 3 Quota sampling is like stratified sampling, but with an important variation.

13. Microplate sampling adapter

14. The multichannel data sampling system includes three parts i. e analog signal pretreatment circuit, data sampling circuit, data sampling control circuit.

15. Methods Cluster sampling and random sampling Methods: Were used to choose the subject.

16. Extremism became tolerance.

17. From Violence to Tolerance

18. Convenience sampling is the most common form of nonprobabilistic sampling, mostly because it is misused

19. The provisions for sampling at retail stage should be aligned with the general sampling procedures.

20. Active current mode sampling circuit

21. 4.3.6 - Aseptic SAMPLE Aseptic sampling is a technique used to prevent contamination by your sampling method

22. The produced gas stream volumina are infinitely variable to be adjusted to the sampling volumina of different sampling systems (e.g. personal pumps for personal-air-sampling).

23. Aoap ILLUSTRATED SAMPLING Figure 4 - Oil Sampling Tube Figure 6 - Oil Analysis Drain Method APPENDIX D

24. I have low alcohol tolerance.

25. The quality could be acceptable if a sampling strategy of 10 per cent sampling ratio is adopted.

26. The estimation of the sampling variance must take into account the sampling design and changes of strata.

27. provisions for collecting, sampling and transport of biological agents from the sampling point to the place of treatment;

28. Methods for measurement, sampling and analysis

29. The tolerance to the impact velocity is ± 2 % and the tolerance to the impact direction is ± 2°.

30. • Alpha Test of the Sampling Methodology

31. D Exactly above the sampling outlet

32. Sampling Procedures Ambient concentrations of benzene are measured using a set of standard sampling and analytical methods

33. Acceptance and compliance sampling shall be in accordance with officially sanctioned Measurement Canada sampling plans as applicable.

34. The indicators are about the ‘Abiotical’ factors such as climate, soil, salt tolerance and heavy metal tolerance

35. The Sampling Control Seals are based on a highly adhesive backing in order to repair sacks after sampling.

36. Resource allocation guided by risk tolerance.

37. Tolerance is one of his strengths.

38. Wine sampling Clink! Commemorative Tasting Glass

39. We have zero-tolerance to terrorism.

40. Tolerance to alcohol decreases with age.

41. Tolerance is a sign of breeding.

42. Mike Rowbottom has been sampling it.

43. It explains the basic mechanisms of Chimerism-based tolerance and provides an update on ongoing clinical tolerance trials

44. Languedoc was a land of tolerance.

45. • Halifax Agreement - Acceptance Sampling Plan Documentation 2005

46. Type of Contaminant Test Test Method Used Medicinal Substance Tolerance Limits Acceptable NHPD’s Tolerance Limits Chemical Contaminants Arsenic

47. Compressor lubricant sampling, analysis of oil quality.

48. Common Buckthorn has a broad environmental tolerance

49. Zero tolerance policy applies to all citizens.

50. He had a high tolerance for opiates.

51. There should be zero tolerance towards terrorism.

52. 3.5 Measurement Canada - Meter Sampling Program Adaptability

53. Halifax Agreement - Acceptance Sampling Plan Documentation 2005

54. - Activated sludge : sludge sampling sites and concentration,

55. Tolerance is classified into central tolerance or peripheral tolerance depending on where the state is originally induced—in the thymus and bone marrow (central) or in other tissues and lymph nodes (peripheral).

56. Aragonite aids concentration and brings tolerance and …

57. Hemophilia treatment Immune tolerance : a nursing perspective.

58. Bioprospector uses a stochastic Gibb's sampling alignment algorithm

59. · On-site sampling of airborne dusts and gases

60. Long term tolerance however is an issue .

61. Tolerance is one of her many strengths.

62. Acceptance, forgiveness, and tolerance foster peaceful relationships.

63. Adaptive predistortion linearized amplifier system employing selective sampling

64. All samplers yielded equivalent levels of sampling precision.

65. Table for Acceptance — Rejection Sampling Plan by Attributes

66. Problems of sampling and analytical procedures are discussed.

67. Identify the observers who will do the sampling.

68. The techniques (amniocentesis, chorionic villus sampling, fetal blood sampling, placentocentesis, fetal cells from maternal blood) all involve obtaining fetal cells for analysis.

69. Due to the uncertainties regarding the sensitivity of this strategy, it is needed that food businesses operators using this alternative establish a sampling plan, including sampling procedures and sampling points of the spent irrigation water.

70. Table for acceptance/rejection sampling plan by attributes

71. But Tobias had a low tolerance for alcohol

72. 8 Tolerance exists only for officially sanctioned ideas.

73. • specify sampling and laboratory methods in advance; and

74. • A plan to be used for Acceptance Sampling

75. Health certificate and results of sampling and analysis

76. Results of sampling and analysis and health certificate

77. 24 Six subjects did not consent to a glucose tolerance test and tolerance was determined from fasting plasma glucose and insulin concentrations.

78. Angularity applied on non feature of size creates tolerance zone consists of two parallel planes and all the surface elements must lies within tolerance zone. When Angularity is applied on cylindrical feature of size, tolerance zone is a cylinder, diameter of tolerance value referenced in feature control frame

79. We firmly believe in zero tolerance against terrorism.

80. Employer has zero tolerance policy on alcohol use.