1. Angle of visibility in the horizontal plane: ...

2. Angle of visibility in the horizontal plane

3. Angle of the visibility in the horizontal plane

4. Cornice definition is - the molded and projecting horizontal member that crowns an architectural composition.

5. Mustard exists, just like tomato sauce, on a horizontal plane.

6. P4 - a plane containing straight line OQ and forming an angle of 8o below the horizontal plane.

7. P3 - a plane containing right angle OQ and forming an angle of 10o above the horizontal plane;

8. P#-a plane containing straight line OQ and forming an angle of #o below the horizontal plane

9. P#-a plane containing right angle OQ and forming an angle of #o above the horizontal plane

10. a plane passing through the straight line OQ and forming an angle of 10° above the horizontal plane,

11. a plane passing through the straight line OQ and forming an angle of 10° above the horizontal plane;

12. a plane passing through the straight line OQ and forming an angle of 10o above the horizontal plane,

13. a plane passing through the straight line OQ and forming an angle of 8o below the horizontal plane.

14. a plane passing through the straight line OQ and forming an angle of 8° below the horizontal plane.

15. A plane passing through the straight line OQ and forming an angle of 8° below the horizontal plane.

16. A plane passing through the straight line OQ and forming an angle of 10° above the horizontal plane;

17. The plane dropped lower, returning to the horizontal, and the airfield appeared.

18. P4 - a plane passing through the straight line OQ and forming an angle of 8° below the horizontal plane.

19. P3 – a plane passing through the straight line OQ and forming an angle of 10° above the horizontal plane,

20. P3 - a plane passing through the straight line OQ and forming an angle of 10° above the horizontal plane,

21. Abscissa is the value of the horizontal axis on a coordinate plane.

22. The definition of an Abscissa is the horizontal coordinate on a geometric plane

23. In astronomy the horizon is the horizontal plane through the eyes of the observer.

24. tangent of angle subtended by slope of 18 per cent and horizontal plane = 0,18

25. cosine of angle subtended by slope of 18 per cent and horizontal plane = 0,98418

26. Instead, the Backcast is consciously made in a more horizontal plane than the forward cast

27. Synonyms for Accumbent include decumbent, prostrate, prone, flat, horizontal, reclining, recumbent, level, parallel and plane

28. The horizontal plane through the upper edge of the guiding device is the reference datum.

29. If the axial plane of a fold is essentially horizontal. Then we call it recumbent fold.

30. Recumbent Anticline definition is - an overturned Anticline having its axial plane more nearly horizontal than vertical.

31. The wind influence generates forces in the horizontal plane according to the actual wind speed and direction.

32. All of the lids could rotate in horizontal plane around the center of the erect shaft (4).

33. the vehicle shall be placed on a horizontal plane and the seats adjusted as prescribed in point 2.2;

34. You're projecting!

35. Ambisonics is a surround sound technique covering the horizontal plane as well as regions above and below the listener

36. Two airscrews are mounted vertically at the front and rear of the body such as to be capable of rotating from a vertical plane into a horizontal plane.

37. the plane touching the upper edge of the plate and forming an angle measured upwards of #° with the horizontal

38. The elevation angle is the angle between the horizontal plane and the line of sight, measured in the vertical plane. The Greek letter Epsilon (ε) describes the elevation angle.

39. Attitude provides information about an object's orientation with respect to the local level frame (horizontal plane) and true north

40. 22 The sample is fixed in a horizontal plane and can be examined by rotating it through 360 degrees.

41. An Axonometry consists in projecting the figure, after an orthogonal Cartesian coordinate system and a coordinate plane into which the figure will be projected have been chosen, on the chosen plane for the diagram (figure)

42. the plane touching the upper edge of the plate and forming an angle measured upwards of 15° with the horizontal,

43. –the plane touching the upper edge of the plate and forming an angle measured upwards of 15° to the horizontal;

44. — the plane touching the upper edge of the plate and forming an angle measured upwards of 15° to the horizontal,

45. — the plane touching the upper edge of the plate and forming an angle measured upwards of 15° to the horizontal;

46. the plane touching the upper edge of the plate and forming an angle measured upwards of 15° to the horizontal,

47. The CRF base shall have a pitch angle of 15° ± 10°, above the horizontal plane passing through the ISOFIX anchorages system.

48. The angle of obstruction of each A pillar shall be measured by superimposing in a plane the following two horizontal sections

49. The CRF base shall have a pitch angle of #o ± #o, above the horizontal plane passing through the Isofix anchorages system

50. Capstan definition, any of various windlasses, rotated in a horizontal plane by hand or machinery, for winding in ropes, cables, etc

51. The CRF base shall have a pitch angle of 15o ± 10o, above the horizontal plane passing through the Isofix anchorages system.

52. Catenary cable system must be on level horizontal plane; if the project requires varying cable mounting heights, please consult the factory

53. The angle of obstruction of each A pillar shall be measured by superimposing in a plane the following two horizontal sections:

54. The angle of obstruction of each ‘A’ pillar shall be measured by superimposing in a plane the following two horizontal sections:

55. Ablock of mass m is pulled by means of a thread up an incline plane forming an angle a with the horizontal

56. Projective Conic sectionsThe Conic sections (ellipse, parabola, and hyperbola) can be generated by projecting the circle formed by the intersection of a cone with a plane (the reality plane, or RP) perpendicular to the cone's central axis.The image of the circle is projected onto a plane (the projective plane, or PP) that is oriented at the same angle as the cutting plane (Ω) passing through

57. The vertical projection of said first portion (212) on a horizontal plane entirely contains at least one imaginary square of size 15x15 centimeters.

58. 27 In distinctive low-wing flight wings are hardly raised above horizontal plane and depressed far down below body at bottom of downstroke.

59. I'm not great at projecting authority.

60. Airstream Tilt Blowpipe with Black Projecting

61. A projecting land mass; a promontory.

62. 3 They were projecting a new waterworks.

63. 1 You're projecting your insecurity onto me.

64. Are projecting inquietude Affronting preference saw who

65. The Ailerons are horizontal flaps located near the outer end of an aircraft’s wings and are used to bank the plane to facilitate a turn

66. You're projecting your insecurity onto me.

67. Instrumental vertical and horizontal adjustment — horizontal line scan method

68. Polarization: Horizontal

69. HORIZONTAL CANAL

70. Align Horizontal Distribute

71. Align Horizontal Middle

72. Figure 2: Instrumental vertical and horizontal adjustment- horizontal line scan method

73. Civil-Horizontal Valve

74. Circuit-Horizontal Capacitor

75. With horizontal trimming die, horizontal trimming pro- cess can be fulfilled.

76. Horizontal motion detector

77. Free from insecurity that the world's projecting onto me.

78. Civil-Horizontal Compressor

79. Emboss Horizontal Only

80. The lateral abutment surface (4) is inclined at a first angle (α) of predetermined value to the horizontal plane (π) at least at the second end position (7).